油-气-水三相流超声传感器持气率测量*

为探索油-气-水三相流持气率测量难题,该文开展了脉冲透射式超声传感器持气率测量动态实验研究。首先,利用超声传感器与光纤传感器组合,测取了油-气-水三相流中段塞流、混状流、泡状流的响应信号;其次,提取了超声脉冲信号的最大值序列来反映不同流型时超声传感器响应特性,同时,借助双头光纤传感器与相关测速法,计算得到了流体中气泡弦长序列;最后,结合流型与泡径信息,利用超声传感器测量了不同流型下持气率,并分析了不同流型持气率预测的误差来源,为其他油-气-水三相流持气率测量传感器设计提供了借鉴。     

Damage characteristics and surface description of near-wall materials subjected to ultrasonic cavitation

For the analysis of ultrasonic cavitation erosion on the surface of materials, the ultrasonic cavitation erosion experiments for AlCu4Mg1 and Ti6Al4V were carried out, and the changes of surface topography, surface roughness, and Vickers hardness were explored. Cavitation pits gradually expand and deepen with the increase of experiment time, and Ti6Al4V is more difficult to erode by cavitation than AlCu4Mg1. After experiments, the cavitation damage characteristics such as the single pit, the rainbow ring area, the fisheye pit, and some small pits were observed, which can be considered to be induced by a single micro-jet impact, ablation effect caused by the high temperature, micro-jet impingement with a sharp angle, and multibeam micro-jets coupling impact or negative pressure in the local area produced by micro-jet impact, respectively. The surface roughness and Vickers hardness of the material increase slowly after rapid growth at different points in time as the experiment time increases. With the increase of the ultrasonic amplitude, both of them first increase and then decrease after the ultrasonic amplitude is greater than 10.8 μm. The increases in surface roughness and Vickers hardness tend to decrease as the viscosity coefficient increases. Ultrasonic cavitation can cause submicron surface roughness and increase surface hardness by 20.36%, so it can be used as a surface treatment method.     

Experimental studies on the effect of ultrasonic treatment and hydrogen donors on residual oil characteristics

Residual oil, the residue after the distillation of crude oil, imposes deleterious effects on refinery due to its high viscosity and asphaltene content. In this context, ultrasonic technology has been widely applied in refining processes given its high efficiency and minimal environmental impacts. To guide the selection of operation parameters, in this work, we probed the effect of treatment duration, power, and hydrogen donor on the characteristics of residual oil under ultrasonic treatments. Underlying mechanisms of ultrasonic treatments, in the absence and presence of hydrogen donors, were verified through systematically analyzing viscosity, component conversion, molecular weight, hydrogen distribution, and functional groups of residual oil. While viscosity reductions under low-power density treatment are caused by colloidal system disaggregation, high-power density treatment can bring in both chemical bond cleavage and colloidal system disaggregation. In addition, adding hydrogen donor can effectively prevent radical recombination, and thus increases the yield of saturate. These results provide fundamental understandings on the effects of ultrasonic treatments.     

超声筛查早期诊断婴儿发育性髋关节异常的临床管理

目的 了解鄞州区0~6月龄婴儿发育性髋关节异常（developmental dysplasia of hip,DDH）的流行病学特征，探讨DDH 的临床管理模式。方法 由鄞州区妇幼保健机构社区医师和鄞州区第二医院围生医生共同负责完成DDH 的临床初筛工作，可疑或异常者转儿科进一步检查，并予B 超筛查，对不同人群分别进行早期干预、复查、随访及骨盆正位X 线片检查，必要时转小儿骨科治疗。结果 2012 年5 月至2013 年5 月，共6 890 例0~6月龄婴儿进行髋关节B 超筛查，初筛阳性率5.73%（395/6 890），复查阳性率0.59%（34/5729）；月龄越小筛查阳性率越高，差异有统计学意义（P＜0.05）。新生儿及1~3月龄婴儿初筛阳性率高，但复查阳性率明显降低，差异有统计学意义（P＜0.05）；4~6月龄婴儿初筛及复查阳性率差异无统计学意义（P ＞0.05）。结论 鄞州区采取的社区门诊检查- 区医院儿科复查-B 超筛查及转诊治疗的管理模式，可作为基层推进DDH 的早发现和早治疗的有效手段。     

多路Marx并联高压脉冲电源研究

脉冲功率技术在工业和生物医学领域有着广泛的应用,很多应用场合要求输出数百安培的高压脉冲。固态Marx发生器虽已研究多年,但是被广泛采用直插封装的IGBT和MOSFET功率半导体开关管的额定电流通常都低于100 A,无法满足低阻抗负载的应用需求。为提高输出脉冲电流幅值,提出两种多路Marx发生器并联的脉冲电源的拓扑结构,第一种方案采用多路Marx发生器直接并联,第二种是共用一组充电开关管的多路Marx发生器并联。由FPGA提供充放电控制信号,采用串芯磁环隔离驱动方案实现带负压偏置的同步驱动,主电路选用开通速度快、通流能力强的IGBT为主开关的半桥式固态方波Marx电路。实验结果表明,6路16级Marx直接并联的脉冲发生器能输出重频100 Hz高压方波脉冲幅值可达10 kV,在30Ω负载侧输出峰值电流可达300 A,上升时间230 ns。共用充电开关管的6路4级Marx并联发生器在5Ω电阻负载上的输出电流峰值可达300 A,最大输出电流可达460 A,上升时间272 ns。表明多路Marx发生器并联可以有效地减小系统内阻,提高系统带载能力;改进后的并联方案实现大电流脉冲输出的同时,所采用的开关管数量减小近一半,提高了系统的抗干扰能力的同时,降低了脉冲电源的成本;且增加级间并联导线可进一步改善均流效果。     

One-step ultrasonic synthesis of Co/Ni-catecholates for improved performance in oxygen reduction reaction

The inherent periodically arranged M−N_X, M−S_X and M−O_X units (M are usually Fe, Co, Ni, etc.) in metal–organic frameworks (MOFs) can be promising active centers in electrocatalysis. In previous studies, MOFs were usually constructed by energy-consuming hydro- or solvo-thermal reactions. Ultrasonic synthesis is a rapid and environment-friendly technique when envisaging MOFs’ industrial applications. In addition, different synthetic pathways for MOFs may lead to difference in their microstructure, resulting in different electrocatalytic performance. Nevertheless, only a handful of MOFs were successfully prepared by ultrasonic synthesis and few were applied in electrochemical catalysis. Herein, we constructed Ni/Co-catecholates (Ni/Co-CATs) synthesized by one-step ultrasonic method (250 W, 40 KHz, 25 W/L, Ultrasonic clearing machine) and compared their performance in oxygen reduction reaction (ORR) with that of Ni/Co-CATs synthesized by hydrothermal method. Ni-CAT and Co-CAT prepared by ultrasonic showed the half-wave potential of −0.196 V and −0.116 V (vs. Ag/AgCl), respectively. The potentials were more positive than those prepared by hydro-thermal method. And they showed excellent electrochemical stability in neutral solution. The latter was only 32 mV lower than that of commercial Pt/C. The improved performance in ORR was attributed to higher specific surface area and mesopore volume as well as more structural defects generated in the ultrasonic synthesis process, which could facilitate their exposure of electrocatalytic active sites and their mass transport. This work gives some perspective into cost-effective synthetic strategies of efficient MOFs-based electrocatalysts.     

Toward efficient interactions of bubbles and coal particles induced by stable cavitation bubbles under 600 kHz ultrasonic standing waves

The interactions of bubbles and coal particles in 600 kHz ultrasonic standing waves (USW) field has been investigated. A high-speed camera was employed to record the phenomena occurred under the USW treatment. The formation and behaviors of cavitation bubbles were analyzed. Under the driving of these cavitation bubbles, whose size is from several microns to dozens of microns, coal particles were aggregated and then attracted by large bubbles due to the acoustic radiation forces. The results of USW-assisted flotation show a significant improvement in recoveries at 600 kHz, which indicates that the interactions of bubbles and particles in the USW field are more efficient than that in the conventional gravitational field. Furthermore, the sound pressure distribution of the USW was measured and predicted by a hydrophone. The analysis of gravity and buoyancy, primary and secondary Bjerknes forces shows that bubble-laden particles can be attracted by the rising bubbles under large acoustic forces. This study highlights the potential for USW technology to achieve efficient bubble-particle interactions in flotation.     

A study on the spectral,microstructural, and magnetic properties of Eu–Nd double-substituted Ba0.5Sr0.5Fe12O19 hexaferrites synthesized by an ultrasonic-assisted approach

In this study, an examination on the spectral, microstructural, and magnetic characteristics of Eu–Nd double-substituted Ba_0.5Sr_0.5Fe₁₂O₁₉ hexaferrites (Ba_0.5Sr_0.5Nd_xEu_xFe_12−2xO₁₉ (x = 0.00–0.05) HFs) fabricated by an ultrasonic-assisted approach has been presented. An UZ SONOPULS HD 2070 ultrasonic homogenizer with frequency of 20 kHz and power of 70 W was used. The chemical bonding, structure and the morphology of the products were evaluated by Fourier-Transform Infrared (FT-IR) Spectroscopy, XRD (X-ray diffraction), scanning and transmission electron microscopy and techniques. The textural properties of the prepared nanomaterials were examined by using the Brunauer-Emmett-Teller (BET) method. The magnetic properties were studied using a vibrating sample magnetometer (VSM) at room temperature (RT) and low temperature 10 K. The magnitudes of various magnetic parameters including M_s (saturation magnetization), M_r (remanence) and H_c (coercivity) were estimated and evaluated. The M-H loops revealed the hard ferrimagnetic nature for all products at both temperatures. The M_s and M_r values showed a decreasing tendency with increasing degree of Eu³⁺ and Nd³⁺ substitutions whereas H_c values displayed an increasing trend. At RT, M_s, M_r and H_c values lie in the ranges of 63.0–68.8 emu·g⁻¹, 24.6–39.2 emu·g⁻¹ and 2252.4–2782.1 Oe, respectively. At 10 K, the values of M_s, M_r and H_c lie between 87.5–97.1 emu·g⁻¹, 33.5–40.1 emu·g⁻¹ and 2060.6–2417.2 Oe, respectively. The observed magnetic properties make the prepared products promising candidates to be applied in the recording media.